[DFR0221] DFRobot Leonardo with Xbee socket

DFRobot Leonardo with Xbee socket is a Arduino development board based on ATmega32u4 chip and it equips an xbee socket and 3 sensor extension pins which allows to be used for wireless communication module with 2.4G Zigbee,900Mhz version, bluetooth and etc. NOTE: This DFRduino Leonardo is pre-installed with SmartDAQ firmware where user can directly to use it to read data from SmartDAQ app.

More details


$22.90

2 items in stock

  • Currently 5.00/5

Rating: 5.0/5 (1 vote cast)

[DFR0221] DFRobot Leonardo with Xbee socket , 5.0 out of 5 based on 1 ratings

This package includes:

  • 1 x DFRobot Leonardo with Xbee socket with SmartDAQ firmware (6 Analog Pins and 18 Digital Pins)

 

Introduction:

DFRobot Leonardo with Xbee socket is an Arduino Leonardo variant processor.The Arduino Leonardo is based on the ATmega32u4 chip. It is the latest addition to the Arduino family. Compared with the earlier Arduino controllors,by using the ATmega32U4 as its sole microcontroller, allows the Leonardo to be cheaper and simpler to use.Also, because the 32U4 is handling the USB directly, code libraries are available which allow the board to emulate a computer keyboard, mouse, and more using the USB-HID protocol! 

 

Based on the Arduino official Leonardo processor,this one from DFRobot equips an xbee socket and 3 sensor extension pins for your application.The Xbee is commonly used wireless communication module with 2.4G Zigbee,900Mhz version,and etc.The socket makes it possible for you to extend the xbee or  XBee form factor wifi,bluetooth and RF modules for your Arduino directly.However,the D14~D16 extension pins with power supply maximize the use of your ATmega32u4 microcontroller.They support the digital sensors and module from DFRobot directly. 

 

Notes: This board is only supported in the latest Arduino IDE 1.0.1 or later version so you will also need to update the IDE.

NOTE: This DFRduino Leonardo is pre-installed with SmartDAQ firmware where user can directly to use it to read data from SmartDAQ Android app. 

 

Specification:

  • Input Voltage (recommended): 7-12V
  • Input Voltage (limits): 6-12V
  • Microcontroller:ATmega32u4
  • Operating Voltage: 5V
  • Interface: Micro USB
  • Compatible with Arduino R3 series pin mapping
  • Directly support Xbee and XBee form factor wifi,bluetooth and RF modules
  • Extend D14~D16 digital pins with 5v power supply
  • Clock Speed 16 MHz
  • Size: 70x55x14mm
  • Microcontroller Specification
    • Digital I/O Pins: 20
    • PWM Channels: 7
    • Analog Input Channels: 12
    • DC Current per I/O Pin: 40 mA
    • DC Current for 3.3V Pin: 800 mA
    • Flash Memory 32 KB (ATmega32u4) of which 4 KB used by bootloader
    • SRAM: 2.5 KB (ATmega32u4)
    • EEPROM: 1 KB (ATmega32u4)



Download:

  • Wiki Doc: Link
  • Arduino source code (UNO, MEGA 2560 & Leonardo) for SmartDAQ : Link
  • Atmega32u4 datasheet: Link
  • Schematic: Link
  • Arduino Leonardo product page: Link
  • Latest Arduino IDE: Link

 

Video Tutorial:

SmartDAQ Android App with DFRobot Leonardo (Arduino Leonardo Compatible):



Cart  

No products

Shipping $0.00
Total $0.00

Cart Check out

PayPal